Jul 26 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Jul 26 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Jul 26 2025 12:00:14 orcad: startLoggingCTD19Plus(): Failed sending OUTPUTFORMAT=3 command after two attempts. Jul 26 2025 12:00:14 orcad: profile(): Failed to activate the CTD! Jul 26 2025 12:00:14 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Jul 26 2025 12:00:16 orcad: syncHydroTime(): The ctd clock was behind by 68 seconds! 1753556414 1753556346 Jul 26 2025 12:00:23 orcad: setCTD19PlusTime(): Failed sending HHMMSS=120016 command. Jul 26 2025 12:00:23 orcad: syncHydroTime(): Could not set the CTD time! Jul 26 2025 12:00:23 orcad: runJobs(): Failed to sync CTD time! Jul 26 2025 12:00:23 orcad: runJobs(): Completed mission: Deep_Cast_Direct Jul 27 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Jul 27 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Jul 27 2025 12:00:14 orcad: startLoggingCTD19Plus(): Failed sending OUTPUTFORMAT=3 command after two attempts. Jul 27 2025 12:00:14 orcad: profile(): Failed to activate the CTD! Jul 27 2025 12:00:14 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Jul 27 2025 12:00:16 orcad: runJobs(): Completed mission: Deep_Cast_Direct Jul 27 2025 13:03:34 orcad: cleanup(): Caught exit signal ( 15 )! Attempting to shutdown cleanly... Jul 27 2025 13:03:34 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:03:48 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:03:52 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:03:52 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:03:52 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:03:52 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:03:52 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:03:52 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:03:56 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:03:56 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:03:56 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:03:56 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:03:56 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:03:57 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:03:59 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:03:59 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:03:59 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:03:59 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:03:59 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:03:59 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:03 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:03 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:03 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:03 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:03 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:03 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:07 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:07 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:07 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:07 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:07 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:08 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:10 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:10 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:10 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:10 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:10 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:10 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:12 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:12 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:12 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:12 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:12 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:13 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:15 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:15 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:15 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:15 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:15 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:15 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:19 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:19 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:19 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:19 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:19 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:20 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:22 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:22 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:22 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:22 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:22 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:22 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:26 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:04:26 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:26 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:26 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:26 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:26 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:30 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:04:30 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:30 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:30 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:30 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:31 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:33 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:33 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:33 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:33 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:33 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:33 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:37 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:37 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:37 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:37 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:37 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:38 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:40 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:04:40 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:40 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:40 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:40 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:40 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:44 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:44 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:44 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:44 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:44 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:45 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:48 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:48 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:48 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:48 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:48 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:49 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:53 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:04:53 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:53 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:53 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:53 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:53 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:04:57 orcad: initCTD19Plus(): Could not set OUTPUTFORMAT=3 two attempts. Jul 27 2025 13:04:57 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:04:57 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:04:57 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:04:57 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:04:58 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:01 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:05:01 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:01 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:01 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:01 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:02 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:04 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:04 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:04 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:04 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:04 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:04 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:07 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:07 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:07 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:07 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:07 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:07 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:11 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:11 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:11 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:11 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:11 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:11 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:15 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:05:15 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:15 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:15 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:15 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:15 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:19 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:19 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:19 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:19 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:19 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:20 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:24 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:24 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:24 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:24 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:24 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:24 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:28 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:28 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:28 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:28 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:28 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:28 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:32 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:32 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:32 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:32 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:32 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:33 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:35 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:35 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:35 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:35 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:35 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:35 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:37 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:37 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:37 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:37 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:38 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:38 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:40 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:40 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:40 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:40 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:40 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:40 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:44 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:44 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:44 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:44 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:44 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:45 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:49 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:49 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:49 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:49 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:49 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:49 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:51 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:05:51 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:51 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:51 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:51 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:52 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:05:55 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:05:55 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:05:55 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:05:55 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:05:55 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:05:56 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:00 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:00 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:00 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:00 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:00 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:00 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:04 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:04 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:04 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:04 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:04 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:04 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:09 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:06:09 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:09 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:09 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:09 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:09 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:13 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:13 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:13 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:13 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:13 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:14 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:18 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:18 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:18 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:18 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:18 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:18 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:22 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:22 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:22 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:22 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:22 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:22 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:27 orcad: initCTD19Plus(): Could not set NAVG=1 after two attempts. Jul 27 2025 13:06:27 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:27 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:27 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:27 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:28 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:30 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:06:30 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:30 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:30 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:30 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:30 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:32 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:06:32 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:32 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:32 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:32 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:33 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:37 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:37 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:37 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:37 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:37 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:37 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:41 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:41 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:41 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:41 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:41 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:41 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:45 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:45 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:45 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:45 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:45 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:46 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:49 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:06:49 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:49 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:49 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:49 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:50 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:52 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:06:52 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:52 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:52 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:52 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:52 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:06:56 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:06:56 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:06:56 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:06:56 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:06:56 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:06:56 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:00 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:00 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:00 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:00 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:00 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:01 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:05 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:05 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:05 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:05 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:05 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:05 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:09 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:09 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:09 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:09 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:09 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:09 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:13 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:13 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:13 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:13 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:13 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:14 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:17 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:17 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:17 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:17 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:17 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:18 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:22 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:07:22 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:22 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:22 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:22 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:22 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:24 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:07:24 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:24 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:24 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:24 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:25 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:29 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:07:29 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:29 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:29 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:29 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:30 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:33 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:33 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:33 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:33 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:33 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:34 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:38 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:07:38 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:38 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:38 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:38 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:38 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:42 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:42 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:42 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:42 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:42 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:42 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:46 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:46 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:46 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:46 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:46 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:46 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:51 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:07:51 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:51 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:52 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:52 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:52 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:07:56 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:07:56 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:07:56 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:07:56 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:07:56 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:07:56 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:00 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:08:00 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:00 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:00 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:00 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:00 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:04 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:08:04 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:04 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:04 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:04 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:05 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:09 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:08:09 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:09 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:10 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:10 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:10 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:14 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:08:14 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:14 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:14 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:14 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:14 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:16 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:08:16 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:16 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:17 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:17 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:17 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:19 orcad: initCTD19Plus(): Failed to send MP command. Jul 27 2025 13:08:19 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:19 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:19 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:19 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:20 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:23 orcad: initCTD19Plus(): Could not set IGNORESWITCH=y after two attempts. Jul 27 2025 13:08:23 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:23 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:23 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:23 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:24 orcad: Starting up ( version 0.9.17_test )... Jul 27 2025 13:08:28 orcad: initCTD19Plus(): Could not set AUTORUN=n after two attempts. Jul 27 2025 13:08:28 orcad: intializeHardware(): Could not initialize the hydro device! Jul 27 2025 13:08:28 orcad: main(): Could not initialize the hardware! Jul 27 2025 13:08:28 orcad: cleanup(): Caught exit signal ( -1 )! Attempting to shutdown cleanly... Jul 27 2025 13:08:28 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya! Jul 27 2025 13:08:28 orcad: Starting up ( version 0.9.17_test )... GLOBAL PARAMETERS ----------------- isDaemon = 0 debugLevel = 4 configFileName = /usr/local/orcaD/orcad.cfg min_depth = 2 max_depth = 110 parking_depth = 20 data_file_prefix = ORCA2_CAST data_storage_dir = /usr/local/orcaD/data last_cast_num = 25108 weather_data_prefix = ORCA2_MET weather_archive_download_period = 1440 weather_status_filename = weather-status.dat ctd_cal_PA1 = 2.482456e+02 ctd_cal_PA2 = -6.524518e-02 ctd_cal_PA3 = 5.430179e-08 solar_calibration_constant = 6.490000e+00 INFO: Assuming Licor 2420 Light Sensor Amplifier with 0.150 gain compass_declination = 1.600000e+01 meterwheel_cfactor = 1.660000e-01 SERIAL DEVICES -------------- RS232 Port description = A happy little CTD device_type = SEABIRD_CTD_19_PLUS tty = /dev/ttyUSB1 baud = 9600 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = GILLMETPAK tty = /dev/ttyUSB2 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none RS232 Port description = A happy little WeatherStation device_type = S9VAISALA tty = /dev/ttyUSB3 baud = 19200 stop_bits = 1 data_bits = 8 flow_control = none parity = none MISSIONS -------- name = Deep_Cast_Direct start_min = 0 start_hour = 12 start_day_of_month = * start_month = * start_day_of_week = * equilibration_time = 20 aux_sample_direction = down cycles = 1.0 depths = Jul 28 2025 12:00:01 orcad: runJobs(): Running mission: Deep_Cast_Direct Jul 28 2025 12:00:06 orcad: profile(): NOTE: Running profile without a meterwheel. Winch control based on CTD pressure only. Jul 28 2025 12:00:11 orcad: startLoggingCTD19Plus(): Failed sending first INITLOGGING command ( retries = 0 ). Jul 28 2025 12:00:14 orcad: startLoggingCTD19Plus(): Failed sending OUTPUTFORMAT=3 command after two attempts. Jul 28 2025 12:00:14 orcad: profile(): Failed to activate the CTD! Jul 28 2025 12:00:14 orcad: runJobs(): Mission Deep_Cast_Direct profile returned: -2 Jul 28 2025 12:00:16 orcad: syncHydroTime(): The ctd clock was behind by 69 seconds! 1753729214 1753729145 Jul 28 2025 12:00:23 orcad: setCTD19PlusTime(): Failed sending MMDDYY=072825 command. Jul 28 2025 12:00:23 orcad: syncHydroTime(): Could not set the CTD time! Jul 28 2025 12:00:23 orcad: runJobs(): Failed to sync CTD time! Jul 28 2025 12:00:24 orcad: runJobs(): Completed mission: Deep_Cast_Direct Jul 28 2025 12:49:08 orcad: cleanup(): Caught exit signal ( 15 )! Attempting to shutdown cleanly... Jul 28 2025 12:49:08 orcad: cleanup(): All lights are shut off, the stove is off and the cat is fed. Leaving for good. Cya!